日日噜噜噜夜夜爽爽狠狠88av ,热久久这里只有精品1,成人精品视频在线播放99

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

新聞資訊

激光雕刻機激光頭安裝后的注意事項！

來源：http://m.30ex0s8.cn 時間：2020-03-02

如果是用激光雕刻機還是移動后的位置，注意檢查高壓電纜是否斷開，以防觸電。

If using laser engraving machine or moving position, pay attention to check whether the high-voltage cable is disconnected to prevent electric shock.

【激光雕刻機】安裝激光頭后注意事項

[laser engraving machine] precautions after installation of laser head

1. 如果使用激光雕刻機一次或移動位置，請注意檢查高壓電纜是否脫落，以免觸電。

1. If the laser engraving machine is used once or moved, please pay attention to check whether the high-voltage cable falls off to avoid electric shock.

激光雕刻機應防止強烈的震動，移動時應先固定好小車和小車，以免震動引起光路偏差或激光裂紋。

The laser engraving machine shall be protected from strong vibration. When moving, the trolley and trolley shall be fixed first to avoid the optical path deviation or laser crack caused by vibration.

3、注意防止冷卻水結冰，北方天氣寒冷時應特別注意冬季更好更換汽車防凍液，溫度過高，有結垢或污垢堵塞機械沖擊等原因造成激光損傷。

3. Pay attention to prevent the cooling water from freezing. When the weather is cold in the north, it is better to change the automobile antifreeze in winter. If the temperature is too high, the laser damage will be caused by scaling or dirt blocking mechanical impact.

激光雕刻機內部電壓高，非技術人員不應打開機殼進行維修，以防觸電。

The internal voltage of laser engraving machine is high. Non professional technicians should not open the shell for maintenance to prevent electric shock.

激光雕刻機應水平放置在桌面上，不能傾斜。

The laser engraving machine shall be placed horizontally on the table top and shall not tilt.
濟南光纖切割機

6. 確保使用過程中冷卻水循環良好，水質清潔。如果水是臟的和黃色的，及時更換水，避免激光管冷卻不良和爆炸。

6. Ensure that the cooling water circulation is good and the water quality is clean during use. If the water is dirty and yellow, change the water in time to avoid poor cooling and explosion of the laser tube.

7、注意防止底盤內部部件因過度冒煙和潮濕而腐蝕損壞。所以每次清洗完工件后要保持機器的衛生，保持機器的清潔，要做經常性的擦拭。

7. Take care to prevent corrosion damage to internal parts of the chassis due to excessive smoke and moisture. So every time after cleaning the workpiece, keep the machine clean, keep the machine clean, and wipe it regularly.

8、激光雕刻機工作時必須嚴格防止工作人員或其他人員用手或用眼睛來觀察，萬一激光損傷或損傷到眼睛，更好是將蓋子扣死。

8. When the laser engraving machine is working, it must be strictly prevented that the workers or other personnel use their hands or eyes to observe. In case of laser damage or eye damage, it is better to buckle the cover.

9. 請避免水進入設備或工作環境太潮濕。保持機器在干燥和通風的地方。

9. Please prevent water from entering the equipment or working environment. Keep the machine in a dry and ventilated place.

10. 嚴禁拆卸各類接插件。

10. It is strictly prohibited to dismantle all kinds of connectors.

11、雕刻機內的鏡片應及時用無水乙醇或丙酮清洗，并輕輕擦拭放好，擦拭時調整光路。

11. The lens in the engraving machine shall be cleaned in time with anhydrous alcohol or acetone, and placed gently, and the light path shall be adjusted when wiping.

以上都是為您介紹的內容，希望對您有所幫助。如果您想了解更多的知識，可以訪問我們的網站，我們將為您提供更的信息。

All of the above are for you, I hope to help you. If you want to know more, you can visit our website and we will provide you with more professional information.